Lantronix XPress-DR-IAP Uživatelská příručka Strana 116
- Strana / 149
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Binary to Hex
Accept
Incoming
Connections
Serial
Response
Upon
Connection
Active Connection
Startup
Hostlist Hex
Unconditionally None (quiet) No active startup Hostlist N/A
Unconditionally None (quiet) Any character Hostlist E1
Unconditionally None (quiet) Active DTR Hostlist E2
Unconditionally None (quiet) CR (0x0D) Hostlist E3
Unconditionally None (quiet) Manual connection Hostlist N/A
Unconditionally None (quiet) Autostart Hostlist E5
Unconditionally None (quiet) UDP Hostlist N/A
Unconditionally Character No active startup Hostlist N/A
Unconditionally Character Any character Hostlist F1
Unconditionally Character Active DTR Hostlist F2
Unconditionally Character CR (0x0D) Hostlist F3
Unconditionally Character Manual connection Hostlist N/A
Unconditionally Character Autostart Hostlist F5
Unconditionally Character UDP Hostlist N/A
Note: The DSTni-XPress DR DTR signal is hardwired to +12VDC. DTR options are
inactive.
The following connect mode options are for when you use modem emulation:
Table 41 - Connect Mode Options for Modem Emulation
Accept Incoming
Connections
Response Hex
Never Echo 16
Never Without echo 6
Never 1-character response 7
With DTR Echo 56
With DTR Without echo 46
With DTR 1-character response 47
Unconditionally Echo D6
Unconditionally Without echo C6
Unconditionally 1-character response C7
9-4 DSTni-XPress DR User Guide
- DSTni-XPress DR 1
- User Guide 1
- Copyright and Trademark 3
- Disclaimer and Revisions 4
- Declaration of Conformity 5
- Warranty 6
- Sales Offices 7
- Contents 10
- List of Figures 12
- List of Tables 13
- 1.1 DSTni-XPress DR 15
- Introduction 16
- PLC's XPress DR-IAP 17
- 1.4 Serial Interface 19
- 1.5 RJ-45 Serial Connector 20
- 1.7 RJ-45 Ethernet Interface 22
- 1.9 Front Panel Description 25
- 1.10 LEDs 27
- 1.11 Dimensions 28
- 1.13 Power Requirements 29
- 1.14 Reset Switch 29
- 1.15 RS-232/RS-485 Switch 30
- Table 7 - Technical Specs 31
- Getting Started 33
- 2.1.3 Port Number 34
- 2.3.1 DHCP 37
- 2.3.2 AutoIP 37
- 2.4 DeviceInstaller 38
- 2.4.3 Test the IP Address 40
- 2.5 ARP and Telnet 44
- 2.6 Serial Port Login 45
- Configure 47
- 3.2 Using DeviceInstaller 48
- 3.3 Web Manager Page 50
- 3.3.1 Unit Configuration 51
- 3.3.2 Server Properties 52
- 3.3.3 Port Properties 53
- 3.3.4 Update Settings 55
- 3.3.5 Technical Support 55
- 3.4.2 Using the Serial Port 58
- 3.5.1 IP Address 58
- 3.5.5 DHCP Naming 60
- 3.6.1 Baudrate 61
- 3.6.2 I/F (Interface) Mode 61
- 3.6.3 Flow 62
- 3.6.4 Port Number 63
- 3.6.5 Connect Mode 64
- 3.6.6 Remote IP Address 67
- 3.6.7 Remote Port 67
- 3.6.8 DisConnMode 67
- 3.6.10 Pack Control 69
- 3.6.12 Send Characters 70
- 3.6.13 Telnet Terminal Type 70
- 3.7 Expert Settings 71
- 3.8 Security Settings 71
- 3.9 Factory Defaults 73
- 3.11 Get Configuration 73
- 3.12 Set Configuration 74
- 4.1 Protocol Firmware 75
- 4.2.1 Via DeviceInstaller 76
- Firmware 77
- 4.2.2 Via TFTP 79
- 4.2.3 Via Another Unit 79
- 4.2.4 Via the Serial Port 80
- 5.1 Overview 81
- Comm Port Redirector 82
- 5.3 Using Redirector 83
- 5.3.1 Port Setup 84
- 5.3.2 Comm App Setup 84
- 5.3.5 Port Settings 86
- 5.3.6 Listen Mode 86
- 5.3.7 Silent Mode 87
- 5.3.8 TCP Keepalive 87
- 6.1 Technical Support 89
- Troubleshooting 90
- 7.1 Monitor Mode 95
- 0> OK; no error 96
- 8> Wrong parameter(s) 96
- 9> Invalid command 96
- 8.1 UDP Datagrams 97
- 8.2.2 Sending a Setup Record 100
- 8.2.3 The Intel Hex Format 101
- 0300300002337A1E 102
- 8.3 Setup Records 103
- 8.3.1 Channel Parameters 104
- 8.3.2 Interface Mode 105
- 8.3.3 Baud Rate 106
- 8.3.4 Flow Control 106
- 8.3.5 Connect Mode 107
- 8.3.6 Disconnect Mode 108
- 8.3.8 Pack Control 109
- 8.4 IP Addresses 110
- 8.4.3 Host Portion 111
- 8.4.4 Network Address 111
- 8.4.5 Broadcast Address 111
- 8.4.7 Network RFCs 112
- 9.1 Connect Mode Options 114
- Binary to Hex 115
- 9.2 Disconnect Mode Options 117
- 9.4 Interface Mode Options 126
- 9.5 Pack Control Options 127
- 10.1 Class A Network 129
- 10.2 Class B Network 129
- 10.3 Class C Network 129
- 10.4 Network Address 130
- 10.5 Broadcast Address 130
- 10.6 IP Netmask 130
- 10.8 Network RFCs 131
Související produkty a manuály pro Sériové servery Lantronix XPress-DR-IAP
(83 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce